A weigh-in-motion (WIM) system measures the axle and gross weight of vehicles as they drive over sensors embedded in the road, without stopping them. It flags suspected overloads, captures images as evidence and passes data to the toll system. WIM is a screening tool. Formal enforcement normally needs confirmation on a certified static weighbridge.
At a glance
- Typical timeline
- 6 to 12 weeks per site, including pavement preparation and calibration.
- Sensors
- Load cells, quartz or piezo strips, with loops and axle detectors.
- What you receive
- Installed sensors, calibration record, evidence capture setup and TMS interface.
- Key limit
- Dynamic weights are screening values and need static confirmation for penalties.
- Best suited for
- Toll plazas and highway enforcement points.
- Our scope
- Sensors, weighbridge integration, overload alerts, evidence and data integration.
Weigh-in-Motion (WIM) Systems Overview
Overloaded trucks damage roads, bridges and safety margins, and they distort toll revenue because axle count and weight often drive the fee or the penalty. Weigh-in-motion systems let a plaza or enforcement point screen every heavy vehicle at traffic speed, so that only suspected overloads are pulled aside. Our weigh-in-motion work covers sensor installation, calibration, evidence capture and data integration.
A WIM system has four parts: the weight sensors in the pavement, vehicle detection and axle sensing, the electronics and software that compute weights, and the evidence and data layer. Where the plaza also has a static weighbridge, the two are linked. The WIM screens, and the weighbridge confirms. This two step approach is what allows enforcement to work without queues of trucks waiting to be weighed.
We want to be direct about what WIM can and cannot do. Dynamic weight depends on speed, vehicle bounce, road smoothness and sensor condition, and accuracy varies from system to system. It is excellent for screening and for building traffic and overload statistics. It is not a replacement for a certified static weighbridge when a penalty must stand up to challenge.
Road surface is the single largest factor in WIM quality. A sensor in rough, rutted or settling pavement will give noisy results whatever its datasheet says. We assess the road before proposing anything, and we sometimes advise that a section of pavement be rebuilt first, since the money is better spent there than on a better sensor.
Ideal for: Toll plazas and highway enforcement points.
What Our Weigh-in-Motion (WIM) Systems Includes
Our WIM scope runs from sensor installation to the evidence trail and the data link to your toll system.
WIM sensor installation in lanes
We prepare the slot, install sensors, grout and seal them, and add axle detectors and cabinets. You receive installation records and as built drawings. Practical tip: never allow traffic back on a sensor before the grout has cured as specified.
Static weighbridge integration
We link the static weighbridge indicator to the WIM database, so the confirmed weight of a flagged vehicle is stored beside its dynamic weight. Practical tip: confirm the weighbridge is verified under legal metrology rules before using it as a reference.
Overload alerts and evidence capture
We set thresholds and tolerance bands, and capture images, plate, time and weights for each flagged vehicle. Practical tip: agree the tolerance band with the enforcement team in writing, since it decides how many false alerts they will handle.
Data integration with the TMS
Weight, axle and image data are passed to the toll management system with agreed message formats, and tested end to end. Practical tip: obtain the TMS interface document early, because this is the item that most often delays commissioning.
Why overload control fails without proper weighing at speed
Static weighing alone does not scale. If every heavy vehicle must be stopped, weighed and released, the queue becomes the problem, and plazas respond by weighing only a few vehicles at random. Operators learn the pattern and the overloaded trucks route around it or arrive at the quiet hours.
WIM installed carelessly fails the other way. Sensors laid into poor pavement give readings that vary with speed and lane position, so the alerts are unreliable. Staff stop trusting them, and the system turns into an expensive display nobody acts on. A poor calibration is the usual cause, followed by sensors that were never rechecked after resurfacing.
A third gap is evidence. An overload alert without an image of the vehicle, its number plate, the time and the axle weights cannot support a penalty or even a conversation with the driver. The data trail is as important as the weight.
What You Gain
Screening at full traffic speed
Every heavy vehicle is weighed as it passes, so only suspected overloads need to be directed to the static weighbridge, which keeps the road moving and reduces queues.
Alerts with evidence
Each flagged vehicle is stored with images, number plate, time, lane, axle weights and gross weight, giving the enforcement team a complete record to act on.
Link to toll and class data
Weight and axle data feed the toll management system and the vehicle classification layer, which helps check that the correct class is charged.
Traffic and overload statistics
Counts by class, axle load distribution and overload frequency by hour and lane support planning, maintenance budgets and discussions with the authority.
Fewer manual weighing delays
Static weighbridge staff handle a short flagged list instead of random checks, which improves throughput and makes enforcement more targeted.
Calibration and drift tracking
Calibration trucks of known weight, run on a schedule, give a record of sensor drift, so you know when the numbers can be trusted.
How the Work Is Delivered
A WIM project begins with the road, then moves to the sensors and the calibration. Skipping the first step is the usual reason for poor results.
- 1
Road and site assessment
We check pavement type, smoothness, rutting, drainage and the approach length before the sensor. We also examine traffic speed, lane discipline and available power and communications. The result is a clear yes, or a list of pavement repairs needed first.
- 2
Design and sensor selection
We choose sensor type and number per lane from the accuracy goal, speed range and budget, and design the detector layout. Weighbridge links, camera positions and the TMS interface are set at this stage.
- 3
Pavement works and sensor installation
We cut and prepare the sensor slot with correct dimensions and flatness, set the sensors in grout and seal them. Curing time is respected, since early traffic damages a sensor before it is tested.
- 4
Electronics, cameras and cabling
Roadside cabinets, cabling, earthing and surge protection are installed, and cameras are positioned to capture the vehicle and number plate with each weight record.
- 5
Calibration with known vehicles
Trucks of known axle and gross weight, weighed on a certified static weighbridge, make repeated runs at several speeds and lane positions. We adjust calibration factors and record the results.
- 6
Alert logic and TMS integration
We set overload thresholds, tolerance bands and alert routes, and connect the data to the toll management system and to the static weighbridge workflow. Alert wording is agreed with the enforcement team.
- 7
Handover, training and recalibration plan
Staff are trained to read alerts and evidence. We hand over the calibration record and set a recalibration plan, typically after resurfacing and at regular intervals under an AMC.
How WIM sensors measure weight in motion
WIM sensors measure the force a tyre applies to the road as it passes. Common types are bending plate and load cell systems, which weigh each axle across a platform, quartz piezoelectric sensors, which give high accuracy and stability at a higher cost, and piezo polymer or ceramic strips, which are cheaper and more sensitive to temperature and speed. Each type has a range of accuracy that depends on installation quality. International guidance such as ASTM E1318 and OIML R134 describes WIM performance classes and test methods, and we use them as references when agreeing an acceptance procedure.
A WIM station also needs axle detectors or loops to count axles and measure speed, plus a controller that computes axle and gross weights. Temperature compensation matters for some sensor types, because summer pavement in Rajasthan, Madhya Pradesh and Gujarat can be very hot. Cameras linked to the record capture evidence. The weighbridge link is a data exchange, so the static weight of a flagged vehicle is stored beside its dynamic reading, which gives the operator a direct view of how well the WIM is tracking.
ASTM E1318 and OIML R134 references
These documents define WIM accuracy classes and test approaches. We use them to structure the acceptance test, and agree which class applies to your purpose.
Static weighbridge legal metrology
A static weighbridge used for penalties must be verified and stamped under legal metrology rules. WIM data supports screening and does not replace that legal step.
Pavement smoothness and approach
The approach pavement should be smooth and level for a defined length before and after the sensors. We record measured conditions and recommend repairs before installation.
Calibration vehicle rule
Calibration uses vehicles of known weight weighed on a certified weighbridge, and runs are repeated at varied speeds and lane positions, so the factors reflect real traffic.
Evidence handling and data protection
Images of number plates are stored with access control and retention limits, in line with the client's obligations under the Digital Personal Data Protection Act 2023 where it applies.
Worked example: WIM screening on two heavy vehicle lanes
Imagine a highway plaza with two lanes carrying a high share of loaded trucks, and a static weighbridge off the main carriageway. The authority wants overloaded vehicles identified without stopping every truck. The approach pavement is concrete in good condition, with a short patch of rutting before the plaza that needs repair.
We would repair the rutted patch first, then install WIM sensors in both lanes with axle detectors, a roadside cabinet and two cameras per lane. Calibration trucks of known weight run several passes at different speeds. We set alert thresholds with a tolerance band, link alerts to the evidence images and send flagged vehicles to a lane that leads to the static weighbridge.
In the typical outcome, the weighbridge staff see a short list of flagged vehicles instead of random checks, and most flagged vehicles are confirmed as overloaded on the static scale. Some are not, and these tell the operator how tight the tolerance band should be. Over a few months the data shows the share of overloaded vehicles by hour, which helps target enforcement shifts.
- Overload screening at traffic speed with no new queue at the plaza
- Evidence package of images, plate, time and axle weights for each flagged vehicle
- Dynamic and static weights stored side by side for tuning
- Hourly overload statistics available for enforcement planning
This is an illustrative scenario built from typical site conditions. Actual quantities, timelines and results depend on your site survey.
Weigh-in-Motion (WIM) Systems Across Four States
We are based in Nashik and deliver across Maharashtra, Gujarat, Madhya Pradesh and Rajasthan. Each state has its own utilities, approvals and site conditions, and these are the points that matter most for this service.
Maharashtra
Heavy mining, steel and agricultural freight leads to overloading on state and national highways. Monsoon damages pavement and can disturb sensor grouting, so we check approach smoothness after each rainy season. A certified static weighbridge for calibration trucks is usually available near industrial belts.
Gujarat
Heavy industrial and port freight on NH 48 and other Gujarat corridors makes overload screening valuable. Coastal humidity and salt affect cabinet electronics, so we use sealed, coated enclosures. Pavement on busy sections wears fast, which means recalibration after resurfacing is not optional.
Madhya Pradesh
Mineral, cement and agricultural freight makes overloading common on several corridors. Concrete and bituminous pavements vary widely, so the road assessment is the first deliverable. Monsoon and hot summers both stress sensor grout and seals, and we plan inspection after each season.
Rajasthan
Extreme summer pavement temperature affects temperature sensitive sensor types and bitumen softness, which changes dynamic weights through the day. We choose sensors and compensation accordingly, and calibrate at more than one time of day. Desert dust and long remote stretches shape cabinet and power design.
Where This Work Is Most Often Needed
Why Teams Work With Us on This
We start with the road
Our first output is an honest view of whether your pavement can support WIM, with repairs listed if not. This avoids spending on sensors that cannot perform.
Civil, electrical and data in one scope
Sensor slots, roadside cabinets, power, surge protection, cameras and the TMS link are handled by one team, which removes the finger pointing between pavement, electrical and software vendors.
Calibration records you can show an auditor
We document every calibration run, the vehicles used and the factors set, so the authority can see how the system was proven and when it needs rechecking.
Recalibration visits from Nashik
Our Nashik team can return for recalibration after resurfacing or monsoon damage, with visits planned by route across Maharashtra, Gujarat, Madhya Pradesh and Rajasthan. Service levels are agreed in the contract for each site.
Need AMC for an existing system?
We maintain installations done by other vendors too, after a short audit of what is already on site.
Guides and Projects Related to This Service
Frequently Asked Questions
01What is a weigh-in-motion system?
A weigh-in-motion system weighs vehicles as they drive over sensors in the road, without stopping them. It measures axle and gross weight, flags suspected overloads and captures evidence images. It is mainly a screening tool, with suspected overloads sent to a static weighbridge for confirmation.
02Is WIM accurate enough for penalties?
Usually not by itself. Dynamic weights vary with speed, road condition and sensor type, so most enforcement regimes require a verified static weighbridge reading before a penalty. WIM tells you which vehicles to check, which makes static weighing far more efficient and better targeted.
03How long does a WIM installation take?
Plan on 6 to 12 weeks per site, including pavement preparation, sensor installation, curing, electronics and calibration. Pavement repair and the availability of a certified static weighbridge for calibration trucks are the usual causes of delay.
04What affects WIM accuracy the most?
Road smoothness, sensor type and installation quality, vehicle speed, temperature and calibration. A smooth, level approach matters more than almost anything else. We measure the pavement first and agree a calibration plan, so you know what accuracy to expect before you commit.
05How often does a WIM system need recalibration?
Recalibrate after any resurfacing or sensor repair, and at regular intervals set in the AMC, commonly once or twice a year depending on traffic and temperature swings. Track drift by comparing WIM weights with static weights of flagged vehicles, which gives an early warning.
06Can WIM work together with the toll system?
Yes. WIM data can be passed to the toll management system with the axle count and images, so the class charged can be checked against detected axles and weight. The interface needs a message specification from the TMS vendor, which we test end to end before go live.

