Industrial Safety Analytics (PPE, Fire & Smoke): ai enabled cctv camera monitoring a facility entrance
AI CCTV & Video Analytics

Industrial Safety Analytics: PPE, Restricted Zones, Fire and Smoke Detection

Spot missing helmets, zone breaches and early smoke on camera, so supervisors can correct a hazard while it is still a near miss.

Since 2014
Based in Nashik
500+ Clients
Across four states
Survey to AMC
One accountable team
Written and reviewed by the Shruti IT Service engineering team, Nashik. Last updated November 2026.
In short

Industrial safety analytics uses existing or new cameras and AI software to detect missing PPE such as helmets and vests, people in restricted or machine-proximity zones, and visual flame or smoke cues. It sends alerts with snapshots and builds compliance reports. Video fire detection supplements code-required detectors and alarm systems. It never replaces them.

At a glance

Typical timeline
Three to eight weeks, mostly camera positioning, rule tuning and a trial period.
Key standards
IS 2189 and NBC 2016 Part 4 for fire detection, IEC 62676, ONVIF.
What you receive
Camera views, detection rules per zone, alert routes, violation snapshots and compliance reports.
Best suited for
Manufacturing, construction, chemical, warehousing and EPC project sites.
Our scope
Survey, camera design, supply, installation, rule tuning, alert integration, training and AMC.
Site survey
Walk with your EHS officer through each hazard zone, at working hours.
OVERVIEW

Industrial Safety Analytics (PPE, Fire & Smoke) Overview

Industrial safety analytics turns a camera into a safety observer. The software looks for specific conditions on the shop floor or site: a person without a helmet or high-visibility vest, someone stepping inside a marked zone around a press or forklift route, or visual signs of flame and smoke. When a condition appears, an alert is sent with a snapshot, and the event is logged for review.

Safety officers cannot be everywhere, and most violations happen when nobody senior is looking. A worker removes a helmet for a minute on a hot day. A contractor crew takes a shortcut through a forklift lane. Analytics will not replace training or supervision, but it gives your EHS team a record of where and when lapses happen, so the training and the layout can be fixed where it matters.

Video fire detection is a different topic from PPE, and we treat it carefully. Cameras can notice flame or smoke in large spaces such as warehouses, yards and workshops, sometimes earlier than a ceiling detector which depends on smoke reaching it. But video analytics is a supplement. The statutory fire detection and alarm system, designed under IS 2189 and NBC 2016, must stay in place.

We design these systems around your safety rules, not around the software menu. Our team, based in Nashik and mobilised to plants across Maharashtra, Gujarat, Madhya Pradesh and Rajasthan, sits with your EHS and production heads to translate each rule into something a camera can actually see, and tell you plainly when a rule cannot be checked by video.

Ideal for: Manufacturing, construction, chemical, warehousing and EPC project sites.

SCOPE OF WORK

What Our Industrial Safety Analytics (PPE, Fire & Smoke) Includes

Our safety analytics scope covers detection rules, camera design and the alert workflow, with video fire cues kept clearly supplementary.

PPE compliance detection for helmets, vests and masks

We set up detection at gates and work zones, with cameras placed at the right distance and height. You receive a rule sheet and trial results per camera. Tip: standardise helmet and vest colours, since detection is more reliable against a consistent look.

Restricted-zone and machine-proximity alerts

We draw zones around hazards and link them to schedules or machine status where possible. Alerts go to supervisors and beacons. Tip: keep painted floor boundaries and software zones identical, so workers see the same limit the system uses.

Video-based flame and smoke detection

We configure visual flame and smoke cues for large open spaces, routed to a human for verification. Tip: treat this as an extra layer and keep your IS 2189 detectors and alarm panel as the primary system.

Violation snapshots and compliance reporting

We store snapshots with time, camera and rule, and build weekly and monthly reports by area and shift. Tip: review reports with supervisors, not only managers, because the people on the floor can explain patterns the data shows.

Alert workflow and review procedure

We map alerts to a review step before action is taken, with a log of outcomes. Tip: agree with HR how alerts may be used, so staff trust the system and see it as a safety tool.

THE PROBLEM WE SOLVE

Why safety rules slip when only people are watching

Safety rules are clear on paper and uneven in practice. Audits happen at scheduled times, and behaviour during an audit is not the daily norm. Near misses go unreported because nobody wants blame. As a result, management sees injury figures after the fact, with little data on the habits that led there.

Existing CCTV rarely helps. Footage is stored for incident review, but nobody watches it live, and nobody can search it for all people without helmets last week. When an accident happens, video shows the event but not the weeks of warning signs before it. The data to prevent it was on the disk and never analysed.

Analytics have their own pitfalls. Helmet detection fails when the camera is too far, when workers wear hoods or caps in similar colours, or at night with poor light. Zone rules fail if the marked zone moves with a machine. Flame and smoke detection can trigger on welding arcs, steam, dust and sunlight reflections. A project that ignores these limits produces many alerts and low trust.

KEY BENEFITS

What You Gain

PPE compliance seen continuously

Cameras at entrances and work zones check for helmets, vests and other visible PPE. Missing items raise an alert and a snapshot, which your supervisor can act on within minutes.

Restricted zone protection

Virtual boundaries around presses, crane paths, pits and live equipment raise alerts when a person enters while the hazard is active. Zones can be time-based, so they apply only during operation.

Early visual cue for flame and smoke

In large spaces where smoke may take time to reach ceiling detectors, video cues can give an early extra warning. The alert is verified by the operator and supports, but does not replace, the fire alarm panel.

Data for safety training

Reports show violations by area, shift and hour. Your EHS team can target toolbox talks where the data shows lapses, rather than repeating the same talk everywhere.

Less reliance on constant patrols

Supervisors respond to verified alerts instead of walking the entire site hunting for violations. Their time goes to coaching and fixing causes.

Records for audits and insurers

Violation logs, snapshots and corrective actions give auditors and insurers a clear view of how you manage risk. They support your safety management system documents.

OUR PROCESS

How the Work Is Delivered

Safety analytics succeed when each rule is written clearly and tested on your own floor. This is how we run it.

  1. 1

    Safety rules and risk review

    We go through your PPE policy, hazard zones and past incidents with your EHS officer. Each rule is classified as something a camera can see reliably, partly, or not at all. This avoids promising checks that video cannot deliver.

  2. 2

    Site walk and camera survey

    We walk each area at working hours, noting lighting, camera height, obstructions, dust, steam, welding and reflective surfaces. For PPE, we aim for a clear view of upper body at roughly 5 to 10 m. The survey marks the points where analytics will work.

  3. 3

    Design and BOQ

    We choose cameras and mounting for each rule, and size the server or edge units for the number of streams. The BOQ includes analytics licences per camera, network, storage and the alert integration. You receive a rule matrix by camera.

  4. 4

    Installation and network work

    Cameras go up at planned heights with protection against dust, vibration and washdown where needed. Cabling uses conduit suited to the plant, and in heavy industrial areas we use shielded cable or fibre to avoid electrical noise.

  5. 5

    Rule setup and trial period

    We configure detection rules, zones and schedules, then run a trial period with alerts going to a test group. We count false and missed detections for each rule, adjust, and report the results to you before any enforcement use begins.

  6. 6

    Alert integration and workflow

    We connect alerts to supervisors by mobile, to a control screen and, where suitable, to signage or a beacon. Escalation rules and a review step avoid disciplinary action based on unverified alerts. We agree the workflow with HR and EHS.

  7. 7

    Training, handover and AMC

    We train EHS staff and supervisors on alerts, reports and rule changes. You receive rule sheets, trial results and as-built drawings. AMC covers lens cleaning, seasonal re-tuning and software updates, with terms agreed per site.

TECHNOLOGY AND STANDARDS

What cameras can and cannot see: PPE, zones and fire cues

PPE detection works by recognising helmets, vests, masks or gloves on a person's body in the image. Accuracy depends on how large the person appears, the camera angle and the colour and contrast of the PPE against the background. Helmets and high-visibility vests are the most reliable. Small items such as safety glasses or earplugs are usually beyond what a normal camera can verify at a working distance. Zone and proximity rules use tracking to see when a person enters a drawn area, with schedules or machine status to switch the rule on.

Video flame and smoke detection looks for flicker patterns, colour and the way smoke moves and spreads. It works best in large open areas with stable lighting, such as warehouses and yards. It struggles with steam, welding flashes, dust clouds and reflections. We set it up as an early visual cue that goes to a human for verification, and we keep it separate from the life-safety fire alarm, which must continue to meet IS 2189 and the NBC.

IS 2189 and NBC 2016 Part 4

These govern selection and installation of automatic fire detection and alarm systems in India. Video detection does not satisfy these requirements. We design it as an addition and flag the code detectors the building still needs.

Factories Act and your safety policy

Your statutory duties as an occupier, and your own PPE rules, define what must be checked. The analytics enforces your rules, but legal compliance stays with your management and EHS function.

IEC 62676 image requirements

We apply its pixel density approach to define how large a person must appear for helmet or vest detection, then test that on site at working distances.

Camera ratings for harsh areas

Dust, washdown and vibration need IP66 or better housings, and for hazardous areas with explosive atmospheres, certified equipment is a separate requirement that we flag early, because normal cameras cannot be used there.

Metrics for missed and false detections

We agree acceptance by detection rate and false alert rate per rule over a trial period, measured on your floor. A single accuracy claim from a brochure is not accepted.

WORKED EXAMPLE

Worked example: PPE and zone analytics at a fabrication plant

Consider a metal fabrication plant near Nashik with a main shop floor, a stores yard and a loading bay. The EHS officer reports frequent lapses in helmet use in the loading bay and people walking through a forklift lane that has a painted but ignored boundary. The plant also has a large warehouse where management wants an extra visual fire cue.

We would add cameras at the loading bay and plant gate for helmet and vest checks at a distance of about 6 m. The forklift lane would get a zone rule active only during working shifts, with an alert to the supervisor and a flashing beacon. In the warehouse, video flame and smoke analytics would send a verification alert to the control desk, while the existing addressable fire alarm remains the life-safety system.

During a four-week trial, the client typically sees which shifts and areas account for most lapses, and a few false alerts from welding flashes and a reflective vest hung on a rack. These are fixed by masking zones and adjusting settings. Weekly reports then feed toolbox talks targeted at the specific bay and shift.

What the client typically sees
  • Helmet and vest lapses logged by area, shift and hour.
  • Forklift lane breaches alerted to supervisors in real time.
  • Warehouse smoke cue verified by an operator, with code detectors untouched.
  • Weekly compliance report used for targeted training.

This is an illustrative scenario built from typical site conditions. Actual quantities, timelines and results depend on your site survey.

SERVICE AREA

Industrial Safety Analytics (PPE, Fire & Smoke) Across Four States

We are based in Nashik and deliver across Maharashtra, Gujarat, Madhya Pradesh and Rajasthan. Each state has its own utilities, approvals and site conditions, and these are the points that matter most for this service.

Maharashtra

Maharashtra has the Maharashtra Fire Prevention and Life Safety Measures Act and a large base of MIDC engineering, auto and chemical plants. Video fire cues must sit beside, not replace, the detection your fire authority requires. Monsoon humidity and welding-bay steam cause false smoke alerts, which we mask during the trial.

Gujarat

Gujarat has its own fire prevention and life safety act, and heavy chemical, petrochemical and pharma clusters in GIDC estates. Hazardous areas with flammable atmospheres need certified equipment, and standard cameras cannot go there. Coastal humidity and salt air call for sealed, corrosion-resistant housings on yard and jetty cameras.

Madhya Pradesh

Madhya Pradesh plants in areas such as Pithampur and Mandideep cover auto, pharma and engineering work with large contract workforces. PPE compliance among contractor crews is often the main gap, so we place gate-side checks. Confirm the local fire authority requirement for any video fire cue you add.

Rajasthan

Rajasthan has cement, mining, stone and textile units in RIICO areas where dust is heavy and temperatures are extreme. Dust clouds trigger false smoke alerts, so we mask known dust sources and rely on operator verification. Helmets and vests are detected well in daylight glare only with the right camera angle. Confirm local fire authority rules.

INDUSTRIES SERVED

Where This Work Is Most Often Needed

Manufacturing and Industrial PlantsWarehousing and LogisticsEPC and Infrastructure ContractorsReal Estate and TownshipsHealthcare and Hospitals
WHY SHRUTI IT SERVICE

Why Teams Work With Us on This

We also install the code-required fire systems

Because we design fire alarm and detection too, we can keep video cues and statutory detectors in their proper roles. You get a clear line between what is supplementary and what is mandatory.

Rules checked for feasibility first

We tell you which of your safety rules a camera can check and which it cannot. That honesty saves you from paying for analytics that will never be accurate.

Trial before enforcement

A measured trial period with logged false and missed detections comes before any disciplinary use. You see the numbers and decide when the system is ready.

Plant-aware installation

Our field team is used to dust, vibration, heat and monsoon moisture in industrial estate plants, and builds housings, cabling and cleaning schedules to match. For plants outside Maharashtra, teams are mobilised from Nashik and visits are planned by route and site cluster.

INSIGHTS AND PROJECTS

Guides and Projects Related to This Service

FAQ

Frequently Asked Questions

01Can video analytics replace smoke and heat detectors?

No, video flame and smoke detection supplements code-required detectors and never replaces them. Statutory fire detection and alarm systems must meet IS 2189 and NBC 2016 Part 4 and your local fire authority's requirements. We use video as an early cue in large spaces and keep the detectors and panel as the life-safety system.

02How accurate is PPE detection?

Helmet and vest detection can be reliable when people appear large enough, lighting is steady and colours contrast with the background. Small items like glasses are not reliably checked by normal cameras. We agree detection and false alert rates per rule in a trial on your own floor, rather than quoting a general figure.

03Will it work with our existing CCTV cameras?

Sometimes. Existing IP cameras can work if resolution, angle, lighting and stream support are suitable and ONVIF or RTSP streams are available. Many old cameras are mounted too high or too far for PPE checks. We assess each camera in the survey and replace or reposition only those that cannot do the job.

04How much does industrial safety analytics cost?

Cost depends on the number of cameras, analytics licences per camera and per rule, server or edge hardware, camera replacement, network work and alert integration. A trial area is a good way to start. We price after a site walk and give a line-item BOQ so licence costs are clear.

05Can the system cause false alerts from welding or steam?

Yes, flame and smoke cues in particular can be triggered by welding flashes, steam, dust and sunlight reflections. We mask known sources, adjust sensitivity and run a trial to measure false alerts. A human verification step stays in the workflow, so a false alert wastes a glance rather than starts an evacuation.

06Can we use the alerts for disciplinary action?

That is your policy decision, but we advise a review step before any action. Use the alerts first for coaching and trend data, and apply formal action only after the trial shows reliable detection and staff have been told how the system is used. Agree the approach with HR and your safety committee.

LET'S BUILD TOGETHER

Ready to Discuss Industrial Safety Analytics (PPE, Fire & Smoke)?

Tell us about your site, timeline and any tender documents. Our Nashik team will respond with a survey plan and a clear scope.

+91 96070 53335
Call Now