Biometric access control uses a fingerprint, face or palm template to decide whether a door unlocks. Shruti IT Service supplies and installs the readers, fail-safe or fail-secure locks, controllers and central software, then sets zone rules and schedules and hands over a tested system with access logs. It suits offices, server rooms, labs and any area where a shared card is not enough.
At a glance
- Typical timeline
- Two to six weeks from approved design for a single floor or building, depending on door readiness and cabling.
- Key standards
- UL 294 style performance classes for readers, IS 732 for wiring, and the DPDP Act 2023 for stored biometric data.
- What you receive
- Door schedule, wiring diagram, tested controllers, configured software, access rules and an admin guide.
- Best suited for
- Offices, server rooms, labs, pharma and R&D areas, cash rooms and any restricted zone.
- Our scope
- Readers, locks, door hardware, controllers, power, software, enrolment and training.
- Site survey
- Door by door check of frame, leaf material, hinge side, cable route and fire exit requirements.
Biometric Access Control Overview
Biometric access control ties entry to something a person is, not something they carry. A card can be lent to a colleague, copied or left on a desk. A fingerprint, face or palm vein pattern cannot be handed over in the same casual way. For a server room, a laboratory or a store with high-value stock, that difference is the whole reason for the project.
A working system has four parts. The reader captures the biometric and matches it, either on the device or on a server. The controller makes the open or deny decision and drives the lock. The lock and door hardware physically hold the door. The software holds the users, the rules and the log. We design all four together, because most failures on site come from a mismatch between them, such as a magnetic lock fitted on a door that must also be a fire exit.
We install biometric systems for offices, IT parks, factories, hospitals and institutions from our base in Nashik, delivering across Maharashtra, Gujarat, Madhya Pradesh and Rajasthan. Many of these sites already have CCTV or a fire alarm from us, so the access system is planned to share cable routes, power backup and the monitoring room instead of adding a separate island.
Biometric is not always the right answer. For a main entrance with several hundred people arriving in ten minutes, a card or a face terminal with fast throughput usually works better than fingerprints. We say this at survey stage and recommend the technology that fits the traffic, the user group and the risk, even if that is a mix of biometric on the inner doors and cards on the outer ones.
Ideal for: Offices, server rooms, labs and restricted areas.
What Our Biometric Access Control Includes
Our biometric access control scope covers everything from the reader on the wall to the log on the screen, so that one team answers for the whole door.
Biometric reader supply and installation
We select fingerprint, face or palm readers by user group and environment, mount them at a consistent height and wire them back to the controller. Tip: test a sample reader with ten of your own staff before ordering a hundred, particularly if workers handle chemicals, oil or cement.
Electromagnetic locks and door hardware
We supply and fit electromagnetic locks, strikes, door closers, exit buttons and door position sensors, and fix door alignment problems that stop locks engaging. Tip: tell us early which doors are fire exits, because that decides fail-safe or fail-secure hardware and sometimes the whole door.
Zone based access rules and schedules
We build zones, user groups and time schedules, with holiday calendars and anti-passback where it is useful. You receive a rules matrix that your security head signs off. Tip: keep groups few and role based, because hundreds of individual exceptions become unmanageable within a year.
Central software with access logs
We install and configure the central software, set admin roles, define alarms such as door forced or held open, and set up report exports. Tip: decide log retention and backup rules at the start, since auditors ask for twelve months of history at the worst moment.
Enrolment, training and handover
We enrol users, fix poor templates and train your admin and reception staff on daily tasks. You receive as-built drawings and a configuration backup. Tip: nominate two admins, not one, so that leave or resignation never leaves the system unmanaged.
Why shared cards and keys fail restricted areas
In most plants and offices the first sign of trouble is not a break-in. It is a question nobody can answer: who opened the server room at 11 pm last Tuesday? Keys have no log. Cards have a log, but it records the card, not the person. If three engineers share one card because the admin was slow to issue more, the log is accurate and useless.
The second problem is slow offboarding. When a contractor or employee leaves, their key may never come back, and their card stays active until someone remembers. Locks get re-keyed at cost, or they do not get re-keyed at all. A biometric template is removed from the central software in seconds, and the person has no credential left to forget to return.
The third problem is poorly matched hardware. Fingerprint readers installed in a dusty workshop, where operators have worn or oily fingertips, reject a large share of genuine users. Staff then prop the door open. A reader that is technically good but wrong for the user group creates exactly the habit it was bought to stop.
What You Gain
Non-transferable entry
The credential is the person. Colleagues cannot lend it, and a lost bag no longer means a lost key to the server room. Audit questions get a named answer.
Reliable audit trail
Every grant, denial and door held open event is logged with time and user. The log exports to CSV or PDF for internal audits and customer security reviews.
Fast offboarding
Remove one user in the software and every door obeys at once. No re-keying, no waiting for a card to be collected from a contractor who has already left.
Zone and time rules
Give the night shift access to the production floor but not the R&D lab. Give housekeeping access only between set hours. Rules live in software and change without touching the door.
Layered security
Combine biometric with a card or PIN for the most sensitive doors. Two factors at the server room, one factor at the corridor, matched to real risk and cost.
Integration ready
Door events can feed the CCTV system, trigger a camera bookmark, release locks on fire alarm and export attendance. One site, one set of records.
How the Work Is Delivered
Every biometric project we run follows the same path, and we adjust the depth of each step to the size of the site.
- 1
Door survey and risk review
We walk each door and note frame type, leaf material, swing, hinge side, cable route and distance to the nearest power point. We ask which doors are fire exits, who uses each door and how many people pass in the busiest ten minutes.
- 2
Design and door schedule
You receive a door schedule listing reader type, lock type, controller location and cable path for every door, plus the zone and user group matrix. We agree this in writing before ordering anything.
- 3
Supply and staging
Controllers are bench configured and labelled before they reach site. Power supplies with battery backup are sized for lock current plus reader load, with margin for the worst door on the circuit.
- 4
Installation and door hardware
Readers go on at a consistent height, locks are aligned on the frame and cables are routed in conduit, not left in false ceilings. Door closers are adjusted so locks actually engage on every swing.
- 5
Testing and fire-release check
We test every door for grant, denial, forced entry, door held open and power failure behaviour. Exit doors are tested with the fire alarm signal so locks release as the design says they must.
- 6
Enrolment and training
We enrol users in batches, check match quality at the reader and fix poor templates on the spot. Your admin is trained on adding users, changing rules and exporting logs.
- 7
Handover and AMC
You get as-built drawings, configuration backups and an admin guide. Support and AMC are agreed per site, covering firmware updates, lock checks and template database backup.
Fingerprint, face and palm: choosing the biometric method
Fingerprint readers are the most common choice and work well in clean office settings. Optical sensors are cheaper but sensitive to dirt and dry skin. Capacitive sensors cope better with moisture and wear. For factories with manual workers, we often recommend face or palm vein instead, because worn fingerprints fail unpredictably. Check the false rejection rate at the reader with your own users, not the brochure figure.
Face terminals are touchless, fast and well accepted since hygiene became a concern, but they need controlled lighting at the reader and a liveness check to defeat photo spoofing. Palm vein readers are accurate and hard to forge, with higher cost per door. Template storage matters as well: on-device storage keeps matching fast and limits what a hacked server can leak, while central storage makes enrolment simpler across many doors. We explain the trade-off and let you choose.
Digital Personal Data Protection Act 2023
Biometric templates are personal data. You need a stated purpose, a way to delete a person's data on exit and controlled access to the template database. We configure retention and admin roles to support this.
IS 732 and good wiring practice
Lock power and controller supply cabling is run in conduit with correct separation from mains cables and proper earthing of metal enclosures. This protects both users and the controller electronics.
Fire and egress requirements, NBC 2016 Part 4
Doors on escape routes must open without a key or special effort. We use fail-safe locks or approved release arrangements and test them against the fire alarm, but approval remains with your fire consultant.
Lock class selection
Electromagnetic locks are rated by holding force, commonly 300 kg for single internal doors. We choose force, fail-safe or fail-secure behaviour and door position sensors to match the door and the risk.
IP and environmental rating
Readers on external or semi-open doors need at least IP65 protection, and a hood against direct sun and rain. We also check operating temperature for Maharashtra summers on west facing walls.
Worked example: biometric control for a 40 door office and server floor
Take a three floor corporate office with 40 controlled doors: 28 internal office doors, 6 labs and storerooms, 4 server and network rooms and 2 stairwell exits. About 350 employees and 60 regular contractors use the building. A survey finds that 26 doors are timber, 10 are glass with patch fittings and 4 are steel fire doors.
The design uses face readers at the main entrance for speed, fingerprint plus card at the four server rooms, and card only at ordinary internal doors where biometrics would add cost without matching the risk. Timber doors get electromagnetic locks with a Z bracket. Glass doors get a strike or a glass door lock, because a magnetic lock cannot be fixed to patch fittings reliably. Stairwell doors use fail-safe locks wired to the fire alarm relay.
Cabling runs to controllers in each floor's electrical riser, each with a battery backed supply sized for peak lock current plus margin. After commissioning, the team enrols everyone over a week in batches by department, tests each door for forced entry and fire release, and gives the facilities head a rule set for contractors with expiry dates.
- Every server room entry linked to a named person
- Contractor access ends automatically on the set date
- Stairwell locks release on fire alarm during test
- Facilities team can add or remove users without a vendor visit
This is an illustrative scenario built from typical site conditions. Actual quantities, timelines and results depend on your site survey.
Biometric Access Control Across Four States
We are based in Nashik and deliver across Maharashtra, Gujarat, Madhya Pradesh and Rajasthan. Each state has its own utilities, approvals and site conditions, and these are the points that matter most for this service.
Maharashtra
Offices, IT parks and MIDC plants dominate. Readers on west facing walls and open corridors face summer heat and monsoon splash, so we specify IP65 units with hoods. Controller supplies need surge protection where MSEDCL supply sags are common, and backup is sized for the lock load.
Gujarat
Chemical, pharma and port linked units in GIDC estates and coastal belts see salt laden humid air that corrodes reader terminals and lock faces. We specify sealed, coated hardware and stainless fixings, and put controllers indoors. Sensitive lab doors usually get face or palm readers where workers handle chemicals.
Madhya Pradesh
Pithampur, Mandideep and Indore based plants mix large workforces with hot summers and a strong monsoon. Worn fingerprints are common among manual workers, so we trial readers with your own staff first. Power from the regional DISCOM can be uneven, so battery autonomy matters.
Rajasthan
RIICO estates and desert sites bring extreme summer heat and fine dust. Optical fingerprint sensors clog and face terminals overheat in direct sun, so we choose units rated for the temperature, use shaded mounting and plan cleaning into AMC visits. Long distances mean spare readers are stocked on site.
Where This Work Is Most Often Needed
Why Teams Work With Us on This
Single window for door and wiring
We handle readers, locks, power, cabling and software together. When a door fails to open, there is one team to call and no argument about which supplier's equipment is at fault.
Fire release tested, not assumed
We test lock release against the fire alarm panel on every escape door and record the result. If we install the fire alarm too, the same engineers handle both sides of that interface.
Nashik based site engineers
Our engineers are mobilised from Nashik for survey, installation and commissioning, and AMC visits are planned by route and site cluster. A failed lock or reader fault then gets a planned site visit, with spare readers and lock coils stocked for the route.
Documents you can audit
You receive the door schedule, as-built wiring, rule matrix, test sheet and configuration backup. When your auditor or a customer asks how the system is set up, the answer is on paper.
Guides and Projects Related to This Service
Frequently Asked Questions
01How much does biometric access control cost?
Cost depends mainly on the number of doors, the reader type and the lock hardware. A face or palm reader costs noticeably more than a fingerprint unit, and a steel fire door with a fail-safe lock costs more than a glass door with a strike. Cabling distance and software licences add to the total. Send us a door list and we will quote per door and for the central system.
02How long does a biometric access control installation take?
A single floor with ten to twenty doors typically takes two to three weeks from approved design, and a multi-floor building four to six weeks. The main delays are door modifications, civil work for cable routes and late power points. Enrolment runs alongside the final testing and usually takes a week for a few hundred users.
03What is the difference between biometric and card access control?
Biometric checks the person, card checks an object. Cards are cheaper per user, faster at busy entrances and easy to issue to visitors, but they can be shared or lost. Biometric suits sensitive doors where identity matters. Many sites use both: cards for general doors, biometric or card plus fingerprint for server rooms and labs.
04Is biometric data safe, and what does the law say?
It is safe when templates are stored securely and access to them is controlled. Most readers store a mathematical template, not an image of the fingerprint or face. The Digital Personal Data Protection Act 2023 treats this as personal data, so you need a clear purpose, consent where required and a way to delete data on exit. We configure the system to support these duties.
05What happens if the power fails or the network goes down?
Controllers keep working because decisions are made locally. A battery backed supply holds the locks and readers for a set autonomy, commonly several hours for a small system. If the network drops, doors continue using stored rules, and logs upload when the link returns. Fire exits release on power loss or alarm, as the egress design requires.
06Can fingerprint readers work for factory workers with worn hands?
Sometimes, but not reliably. Heavy manual work, oil and cement wear down fingerprint ridges, and rejection rates rise. For such user groups we usually recommend face or palm vein readers, or a card at the door with biometric only at the sensitive areas. We test sample readers with your own workers before the final order.

