Structured cabling and network racks in a commercial building
IT Infrastructure

Cat6 or Cat6A? The 100 Metre Rule, Cable Quantity and Certification Tests

How to choose between Cat6 and Cat6A, how the 100 metre channel limit is built up, how to estimate cable quantity for 120 outlets, and which tests a certification report should show.

Shruti IT Service Engineering Team

Survey, design and maintenance engineers, Nashik

Published On

16 Nov 2026

Read Time

8 min read
Share Guide:
Structured cabling and network racks in a commercial building

Cabling is the part of a network that is hardest to change later, because it sits in walls, ceilings and ducts. The choices you make on category, length and testing stay with the building for ten years or more. This guide explains the 100 metre rule properly, shows how to estimate cable quantity, and lists what a real test report should contain.

Key Engineering Takeaways

  • The 100 metre limit is for the whole channel: up to 90 metres of fixed cable plus up to 10 metres of patch cords.
  • Cat6 supports 1 gigabit everywhere in the channel. For 10 gigabit over the full 100 metres, use Cat6A.
  • Estimate cable by multiplying outlets by average run length, then add waste.
  • Ask for certification tests with a printed report for every link, not a simple continuity check.

How the 100 metre limit is made up

A channel runs from the switch port to the device. It includes a patch cord at the switch, the fixed cable between the patch panel and the wall outlet, and a patch cord at the device. The standards allow up to 90 metres for the fixed part, called the permanent link, and up to 10 metres in total for the patch cords, which together make 100 metres.

This is why a measured run of 95 metres from the rack to the outlet is already too long. Plan the route on the drawing, count the vertical drops and the detours around beams, and keep the longest run at or below about 85 to 90 metres to leave some margin.

Cat6 or Cat6A

Cat6 is the common choice for gigabit networks and for powering cameras and access points over Ethernet. At 10 gigabit per second, Cat6 supports shorter distances, commonly quoted at up to about 55 metres under good conditions, while Cat6A supports the full 100 metres.

Cat6A cable is thicker and stiffer, needs more tray space and larger bend radius, and costs more. It makes sense where 10 gigabit to the desk or to Wi-Fi access points is likely during the life of the building, or for backbone links inside a floor. For ordinary office desks and cameras, Cat6 is usually enough, and the saving can be spent on better testing.

Pulling cable too hard or bending it too tightly damages the twists inside, and the fault may not show until a test. Keep to the maker's pulling tension and keep the bend radius at about four times the cable diameter or more.

Worked example: cable quantity for 120 outlets

A floor plate has 120 outlets served from two racks. After marking routes on the drawing, the average run is 45 metres. The total is 120 x 45 = 5,400 metres.

Add 10 percent for waste, service loops and routing changes: 5,400 x 1.10 = 5,940 metres. Cable is commonly sold in 305 metre boxes, so you need 5,940 / 305 = 19.5, which rounds up to 20 boxes. Order one extra box if the site will change during construction.

What a certification test shows

A cheap tester that checks the wires are connected in the right order only tells you the link is not broken. A certification tester measures the link against the category limits and prints a result for each one. The usual tests are wire map, length, insertion loss, near end crosstalk, return loss and propagation delay. Each link gets a pass or a fail, with the margin.

Ask for the results in the maker's file format as well as a PDF, labelled with the outlet number. These records show that the cabling met the standard on the day of handover, and they are the first thing you need if a fault appears later.

Mistakes to avoid

  • Using copper clad aluminium cable, which does not meet the standard and fails PoE loads.
  • Running data cable next to power cable in the same tray with no separation.
  • Leaving no labelling, so that no one can trace a link five years later.
  • Skipping fire stopping where cables pass through fire rated walls and floors.
  • Accepting a pass on a sample of links, when each link can be tested.

Conclusion & Next Steps

Good cabling is quiet. It works, it is labelled and it comes with a test report for every link. Before you approve a quotation, check the category, the longest run, the quantity assumptions and the test report format. We include these in our cabling designs, and we hand over the results with the as built drawings.

Certified Engineering Partner

Need a site survey or project quote?

Our engineers provide comprehensive BOQs, system designs, and turn-key execution across Maharashtra and neighboring states.

Related services

Want this done at your site? These pages explain the scope, the process and the standards we work to.