FTTx & Last-Mile Connectivity: optical fiber cable laid for a campus and highway network
Fiber Optic Network Solutions

FTTx and Last-Mile Fiber Connectivity for Buildings and Tenants

Fiber from the street or point of presence into each building and tenant, designed, installed, activated and documented for ISP and tenant onboarding.

Since 2014
Based in Nashik
500+ Clients
Across four states
Survey to AMC
One accountable team
Written and reviewed by the Shruti IT Service engineering team, Nashik. Last updated November 2026.
In short

FTTx means fibre to the building, home or premises, and last-mile connectivity is the final link from a network point to the user. Most FTTx uses a passive optical network (PON), where one fibre is split to serve many users. Shruti IT Service designs PON layouts, installs splitters, distribution boxes and drops, and activates ONTs for complexes, townships and enterprise branches.

At a glance

Typical timeline
Design 1 to 2 weeks, installation 2 to 8 weeks depending on buildings, units and drop routes.
Key standards
ITU-T G.984 GPON and G.657.A1 drop fibre, APC connectors in PON networks.
What you receive
PON design, splitter and ODB map, drop records, ONT list and ISP onboarding documents.
Best suited for
Commercial complexes, townships, ISPs, and enterprise branch networks.
Our scope
FTTB and FTTH architecture, splitters, ODBs, drops, ONT or ONU activation and documents.
Site survey
Risers, shafts, entry points and unit layouts are inspected to plan drops.
OVERVIEW

FTTx & Last-Mile Connectivity Overview

FTTx covers several ways of bringing fibre close to the user. FTTH takes it into the home or unit. FTTB takes it to the building, with copper or Ethernet finishing the last stretch. FTTP is the general term for fibre to the premises. For a commercial complex, an office tower or a township, the practical question is how many users, how they are laid out and who will provide the service over the network.

Most FTTx networks use a passive optical network. A single fibre from the central point, called an OLT, is split by passive optical splitters, so one fibre serves 32 or 64 users without any powered equipment in the field. Splitters sit in distribution boxes, called ODBs or FDBs, in risers and on floors. From there, thin drop cable runs into each unit and ends at an ONT or ONU that converts light back to Ethernet or Wi-Fi.

Our work covers the physical network inside your property or estate and the connection to the service provider's point. We design the split ratio and layout, install the splitters and boxes, pull and terminate drops, and activate ONTs where the provider authorises it. We also prepare documents the provider and tenants ask for, such as port maps, unit lists and access arrangements.

Some limits are worth stating plainly. We build the passive network and its connectivity, but service plans, bandwidth and billing belong to the ISP or operator. Licences and regulatory approvals for providing services to third parties are the operator's responsibility. Where a property owner wants to run an internal network for tenants, we explain the arrangement options before any design starts.

Ideal for: Commercial complexes, townships, ISPs and enterprise branch networks.

SCOPE OF WORK

What Our FTTx & Last-Mile Connectivity Includes

Our FTTx and last-mile scope covers the passive network inside the property, activation of end equipment, and the records that tenants and providers need.

FTTB and FTTH architecture and PON design

We study building layout and unit counts, choose centralised or distributed splitting, and design the split ratio against the provider's OLT. We plan riser, floor and unit boxes. Tip: ask the provider which split ratio and optics class they support before design, since it fixes the loss budget.

Splitter, ODB and drop-cable installation

We install splitters in ODBs or FDBs, pull feeder and distribution cable through risers, and run thin drop cable to units with correct bend radius. Penetrations are fire-stopped. Tip: use bend-insensitive G.657.A1 drop cable inside buildings, since tight corners are unavoidable.

ONT and ONU installation and activation

We mount and power the ONT or ONU in each unit, connect the drop with a clean APC connector, and activate it with the provider's authorisation and credentials. Tip: confirm power backup for ONTs in critical units, because a PON is only as available as the powered devices at its ends.

Documentation for ISP and tenant onboarding

We deliver riser diagrams, splitter and port maps, unit lists and drop records. Tenants receive a simple connection record. Tip: keep the master port map with the building management, not only with the contractor or the provider.

THE PROBLEM WE SOLVE

Why last-mile fiber projects stall inside buildings

The street connection is rarely the hard part. Delays happen inside the building: no riser space, locked shafts, tenants who will not allow access, drilling restrictions and fire-stopping that has to be restored. A network designed on drawings meets a building that does not match them, and each mismatch costs days.

The second problem is quality of the passive network. Over-split designs, dirty or damaged connectors, tight bends in drop cables and unlabelled boxes cause slow speeds and intermittent drops that tenants blame on the provider. Troubleshooting a PON with no records means opening every box to trace one user.

The third is ownership confusion. When several providers want to serve the same building, nobody is sure who owns the risers, who may enter the boxes and who is responsible for a fault. Without a clear arrangement and documentation, tenants wait while parties argue.

KEY BENEFITS

What You Gain

Gigabit-class service to each unit

A correctly built PON delivers high speeds to every tenant, subject to the provider's plans. Passive splitting avoids powered equipment in risers, which means less to fail.

Lower cost per user

One fibre serves many users, and one riser serves many floors. Compared with running a separate cable to each unit, a PON uses less fibre and less space.

Cleaner risers and neater entries

Planned routes, labelled boxes and fire-stopped penetrations keep the building tidy and make later work easier for any provider.

Faster tenant onboarding

With a unit-by-unit port map and ready drops, a new tenant can be activated in a short visit instead of a fresh survey.

Easier fault tracing

Records identify which splitter port serves which unit, so a fault can be traced from the tenant back to the right box quickly.

Room for more providers or services

Spare fibres, spare splitter ports and clear riser space let you add another provider, camera network or building service later.

OUR PROCESS

How the Work Is Delivered

FTTx work depends on building access, so the process spends more effort on survey and coordination than on cable.

  1. 1

    Building and demand survey

    We inspect risers, shafts, meter rooms and unit layouts, count users and note access rules. We agree with you which provider or providers will use the network.

  2. 2

    PON architecture and loss budget

    We choose centralised or distributed splitting, set split ratios, and calculate loss from the OLT to the farthest ONT, including splitter loss, joints and connectors.

  3. 3

    Permissions and coordination

    We coordinate with building management, fire safety requirements for penetrations and the provider for the point of connection. Any required permissions from the property owner or authorities are tracked.

  4. 4

    Feeder and riser installation

    Feeder and distribution cable is installed in risers with proper support and bend control. ODBs are mounted, labelled and left ready for splitters.

  5. 5

    Splitter and drop installation

    Splitters are fitted, drops are pulled to units, and penetrations are sealed and fire-stopped. Each drop is labelled at both ends and recorded.

  6. 6

    ONT installation and activation

    ONTs are installed, powered and activated by the provider's process. Light levels are checked at the ONT and compared with the design.

  7. 7

    Documentation and handover

    Port maps, riser diagrams and drop records are handed over, and the management team is shown the boxes. An AMC plan covers periodic inspection and fault support.

TECHNOLOGY AND STANDARDS

How a PON works, and what limits it

A PON sends downstream traffic to all users on a shared fibre and gives each ONT a time slot upstream. GPON, defined by ITU-T G.984, is widely deployed and shares about 2.5 Gbps downstream among the users on one PON port. Newer systems such as XGS-PON offer higher shared capacity. The split ratio matters: 1:32 and 1:64 are common, and each doubling of the split adds about 3 dB of loss. A 1:32 splitter typically costs roughly 15 to 17 dB including excess loss, which is why PON links have a tighter loss budget than point-to-point links.

Physical quality decides real performance. PON networks use APC connectors to limit back-reflection, and APC and UPC must never be mixed, because the mismatch adds loss and can damage end faces. Drop cable inside buildings should be bend-insensitive, since sharp turns at doors and ducts are common. Power matters at the ends: ONTs need mains power, so critical users need a small UPS. Finally, a PON is a shared medium, so the provider's oversubscription and plans affect speed as much as the glass does.

ITU-T G.984 GPON

Defines GPON, which sets split ratios and optical budget classes. We design the passive network to match the class the provider's equipment supports.

ITU-T G.657.A1 drop fibre

Bend-insensitive fibre suitable for drops and risers. It tolerates tight corners and reduces installation-induced loss in occupied buildings.

APC connector discipline

A rule for PON networks: use APC connectors throughout, never mix with UPC, and inspect and clean every end face before mating.

Split ratio and loss budget

A design rule: calculate loss from OLT to farthest ONT including splitters, joints and connectors, and keep a margin against the optics class.

Fire-stopping of penetrations

Openings made in shafts and walls for cable should be restored with fire-rated sealing, in line with the building's fire safety requirements and the owner's rules.

Labelling and records

Every box, splitter port and drop is labelled and recorded. It is the main factor in how quickly faults can be traced in the future.

WORKED EXAMPLE

A typical project: FTTH for a 120-unit residential and commercial complex

Picture a complex with two towers and a small commercial podium, 120 units in total. The survey finds two vertical shafts per tower and a ground-floor meter room that can host the feeder termination. The design uses distributed splitting: a 1:4 splitter in each floor box fed by a 1:8 splitter in a riser box, giving 1:32 overall to the provider's OLT port.

Feeder cable runs up the shafts to floor boxes. Drops of bend-insensitive cable go to each unit with proper bend radius, and every penetration is fire-stopped. The loss budget for the farthest unit includes the two splitter stages, about a dozen connectors and joints, and a short distance of fibre, and it is checked against the optics class the provider will use.

ONTs are fitted in each unit and activated with the provider's authorisation. Light levels at each ONT are measured and recorded. The property manager receives a riser diagram, a splitter and port map and a unit-by-unit list, so that future tenants can be connected quickly and any fault traced to its box.

What the client typically sees
  • Each unit has a labelled drop and a recorded light level.
  • Risers are tidy and penetrations are fire-stopped.
  • The property manager holds the master port map.
  • Spare splitter ports allow additional units or a second provider.

This is an illustrative scenario built from typical site conditions. Actual quantities, timelines and results depend on your site survey.

SERVICE AREA

FTTx & Last-Mile Connectivity Across Four States

We are based in Nashik and deliver across Maharashtra, Gujarat, Madhya Pradesh and Rajasthan. Each state has its own utilities, approvals and site conditions, and these are the points that matter most for this service.

Maharashtra

Townships and commercial complexes in Nashik, Mumbai region and other cities usually deal with several ISPs. Agree riser ownership and entry rules early. Monsoon dampness in basement meter rooms affects ODBs, so we choose sealed boxes there and keep ONT power on a backed-up supply from MSEDCL or a society generator.

Gujarat

Dense commercial complexes and townships in cities such as Ahmedabad, Surat and Vadodara often have competing ISPs and a licensee or GUVNL group DISCOM supply. Coastal humidity and salt in nearby towns affect external boxes and connectors, so we specify sealed enclosures and clean APC mating.

Madhya Pradesh

Growing townships and enterprise branches in cities such as Indore and Bhopal need FTTx for tenants and branches. Supply reliability differs between regional DISCOM areas, so we recommend a small UPS at each ONT where service continuity matters, and sealed outdoor boxes for the monsoon.

Rajasthan

Townships, commercial complexes and branch offices face high summer temperatures that raise ONT and cabinet temperatures, and fine dust that settles on connectors. We place ONTs away from direct sun, specify dust-tight outdoor boxes, and inspect and clean every end face before mating.

INDUSTRIES SERVED

Where This Work Is Most Often Needed

Real Estate and TownshipsCorporate Offices and IT ParksEducation and CampusesHealthcare and HospitalsBanking and Financial Services
WHY SHRUTI IT SERVICE

Why Teams Work With Us on This

Passive network built to be audited

Splitter maps, port lists and light levels are recorded as we build, so a fault can be traced from the tenant back to the right box.

Coordination with the other systems

We install CCTV, access control and IT networks in the same buildings, so riser space, power and fire-stopping are planned together instead of by competing contractors.

Used to occupied buildings

Our crews work in occupied buildings and coordinate access with building management and tenants. They are mobilised from Nashik for projects across the four states we serve, and drop installation is scheduled floor by floor to limit disruption.

Support after activation

AMC covers inspection of boxes, connector cleaning and fault tracing, with service levels agreed in the contract for your property.

Need AMC for an existing system?

We maintain installations done by other vendors too, after a short audit of what is already on site.

See AMC options
INSIGHTS AND PROJECTS

Guides and Projects Related to This Service

FAQ

Frequently Asked Questions

01What is the difference between FTTB and FTTH?

FTTH takes fibre all the way into the unit, ending at an ONT in the home or office. FTTB takes fibre to the building, then uses copper or Ethernet cabling for the final stretch to each unit. FTTH gives higher potential speeds and a simpler path to upgrades, while FTTB can cost less where unit cabling already exists.

02What is a PON and how many users can share one fiber?

A passive optical network splits one fibre to many users with passive splitters that need no power. Common split ratios are 1:32 and 1:64. Users share the port's capacity, so real speed depends on the provider's plans and oversubscription as well as the physical network. Each doubling of the split adds about 3 dB of loss.

03How much does FTTx installation cost?

Cost depends on the number of units, building layout, riser access, drop lengths, splitter architecture and what documentation you need. Occupied buildings with difficult routes cost more than new construction with ready ducts. Service charges from the provider are separate. A survey and BOQ gives a firm figure for the passive network.

04How long does it take to connect a building with FTTx?

Typically two to eight weeks for the passive network in a complex, depending on how many units there are and how easy access is. Activation also depends on the provider. We give a schedule after the survey, framed as typical durations that assume building access, permissions and provider coordination are in place.

05Who is responsible for ISP licences and service plans?

The service provider or operator is responsible for licences, regulatory approvals, service plans and billing. We build the passive network and connect it to the provider's point, and we activate end equipment with their authorisation. If you plan to supply services to tenants yourself, take advice on the arrangements first.

06What documents should I ask for after an FTTx installation?

Ask for a riser diagram, a splitter and port map, a unit-by-unit drop list, light level readings at each ONT, and the loss budget. These records let you trace faults, add tenants and invite a second provider. The property manager should keep the master copy, not only the contractor.

LET'S BUILD TOGETHER

Ready to Discuss FTTx & Last-Mile Connectivity?

Tell us about your site, timeline and any tender documents. Our Nashik team will respond with a survey plan and a clear scope.

+91 96070 53335
Call Now